10/100Mbps L2 Stackable Switch
DES-3226S
DES-3226S with 24 10/100Mbps ports.
A DES-332GS stack module installed in the
open slot provides a GBIC port and switch
stacking capability.
24-Port Layer 2 Fast Ethernet Stackable Switch
The DES-3226S is a Stackable 10/100Mbps Layer 2 Switch designed for departmental connection. It provides 24 10/100Mbps
ports, 1 GBIC port for server or fiber backbone connection, and scalable expansion through switch stacking of up to 6 units.
Advanced features such as port trunking, VLANs and priority queues are also provided, allowing a department to
effectively deploy a bottleneck-free switching network for easy integration with a larger enterprise or campus network.
24 10/100Mbps Ports for Workstation Connection
Port Trunks for Aggregated Bandwidths
The switch provides 24 10/100Mbps ports supporting auto-
With low cost per port, port trunking provides an easy and
sensing and auto-negotiation of network speeds and full/half
economical alternative solution for server connection to
duplex. These ports can connect to workstations and print
attain Gigabit bandwidth. Up to 8 10/100Mbps ports or 6
servers, giving each a dedicated bandwidth. All ports
Gigabit ports can be combined together to create a multi-link
support auto MDI-II/MDI-X uplink, allowing you to connect
load-sharing aggregated bandwidth to a server. Trunked ports
to workstations, servers, or other switches from any port
can span multiple units of the stack for fail-safe connectivity
without the need to change your usual straight-through
to mission-critical servers and the network center. Up to 6
twisted-pair cables.
multi-link trunks can be configured for a stack.
Switch Stacking & GBIC Port
VLANs for Enhanced Security & Performance
The switch provides an open slot for installation of a DES-
VLANs improve security and bandwidth utilization by
332GS stack module, which is equipped with a stacking port
limiting the broadcast domains and confining intra-group
and a GBIC port. The stacking port is for switch stacking.
traffic within their segments. To segment up the network,
The GBIC port provides for flexible deployment of multi-
workstations supporting IEEE 802.1Q VLAN Tagging
mode or extended cable-length single-mode fiber. At
connected to the switch can be grouped into different Virtual
2000Mbps full duplex, this port gives you Gigabit server
LANs (VLANs). The switch also supports GVRP (GARP
connection or attachment to a fiber backbone.
VLAN Registration Protocol) for automatic VLAN
configuration distribution.
Scalable Expansion
Up to 6 DES-3226S can be stacked together. You can add
Priority Queues for QoS
units to reach maximum 144 10/100Mbps ports and 6 GBIC
The switch supports Layer 2 802.1p Priority Queue control.
ports per stack. The switches are stacked together through
Each packet going through the switch can be assigned a
high-speed stack cables that provide gigabit per second
queue priority number (in the priority bit). Packets with a
backplane, allowing the entire stack to perform as a single
higher priority number are allowed to pass first. This
entity.
function support allows you to attach IP telephony devices or
video servers to the switch to run delay-sensitive
Flow Control to Prevent Packet Loss
applications like video conference and voice over the
The switch supports standard IEEE 802.3x Flow Control.
Internet.
Working in conjunction with buffer overrun auto-detection,
this full-duplex data transfer mode provides protection
Flexible Transmission Scheduling
against possible data loss for 802.3x supported servers
The switch supports 2 methods of packet transmission
directly connected to the switch.
scheduling: Strict Round-Robin (SRR) and Weighted Round-
DES-3226S
Product Description
10/100Mbps L2 Stackable Switch
Robin (WRR). You can select to use SRR to strictly enforce
SNMP & Web-based Management
your priority queues, or WRR to address bandwidth
The switch stack can be managed from within the LAN
limitations at peak time. WRR allows each queue to be
from an SNMP management station, and via an Internet
assigned a different percentage of the output port's
from any workstation. Standard-based MIBs are built-in,
bandwidth, so that lower-priority queues are not denied
allowing for monitoring and management from third-party
access to buffer space and port bandwidth.
management platforms. Web-based management program
is built into the switch. RMON monitoring is through
IGMP Snooping for Broadcast Control
built-in RMON MIBs.
The switch listens to IGMP (Internet Group Management
Protocol) messages to build mapping table and associate
Optional Ports (Stand-alone Configuration)
forwarding filters. It dynamically configures the switch ports
If you configure the DES-3226S as a stand-alone switch,
to forward IP multicast traffic only to those ports associated
you can install the following modules in the open slot:
with multicast hosts.
- 2-port Fast Ethernet multi-mode fiber module
Broadcast Storm Control
(100BASE-FX)
To limit too many broadcast/multicast flooding in the
- 2-port Fast Ethernet single-mode Fiber module
network, broadcast/multicast storm control is configured to
(100BASE-FX)
screen excessive traffic. Packets are discarded if the
- 2-port Gigabit fiber module (1000BASE-SX)
respective count exceeds the configured upper threshold in a
- 2-port Gigabit fiber module (1000BASE-LX)
given time interval. The possible range of upper threshold is
- 2-port Gigabit copper module (1000BASE-T)
from 0 to 255k packets per second.
- GBIC module (2 ports)
Port Mirroring
Gigabit Over Copper Twisted-pair
This function allows you to mirror adjacent ports for the
The optional Gigabit copper ports provide an inexpensive
purpose of analyzing incoming and outgoing packets where
alternative solution to the fiber. Using your existing low-
packet patterns can be studied.
cost Cat. 5 twisted-pair wires as the transmission media,
these ports allow you to instantly upgrade your servers to
Spanning Tree Protocol
Gigabit capability without requiring you
For mission critical environments with multiple switches
to install new, expensive fiber cables.
supporting STP, you can configure the stack of switches
with a redundant backup bridge path, so transmission and
reception of packets can be guaranteed in event of any fail-
over switch on the network.
Features
24 built-in 10/100Mbps ports
Administrator-definable port security
Switch stacking configuration: 6 units per stack + 6
Port trunking of up to 8 Fast Ethernet ports
GBIC ports
Broadcast storm control
1 open slot for 2 optional Fast Ethernet fiber or 2
802.3x Flow Control
Gigabit ports (stand-alone configuration)
802.1D Spanning Tree for redundant backup bridge Paths
8.8Gbps switching fabric
SNMP, web-based management, RMON monitoring
Auto MDI-II/MDI-X uplink for all twisted-pair ports
Supports 802.1Q VLAN, GMRP multicast, IGMP
Snooping, 802.1p Priority Queues, port mirroring
DES-3226S
Technical Specifications
10/100Mbps L2 Stackable Switch
General
Protocol
DES-132GL Gigabit Fiber Module
CSMA/CD
- IEEE 802.3z 1000BASE-LX standard
- 2 Gigabit fiber ports (SC connectors)
Data Transfer Rates
- Full duplex support
- Ethernet:
- IEEE 802.3x Flow Control
10Mbps (half duplex)
- Cables: single-mode fiber (5 km max.)
20Mbps (full duplex)
- LED report (per port): Link/Act
- Fast Ethernet:
100Mbps (half duplex)
DES-132T Gigabit Copper Module
200Mbps (full duplex)
- IEEE 802.3 10BASE-T/802.3u 100BASE-TX/IEEE 802.3ab 1000BASE-T
- Gigabit Ethernet:
standards
2000Mbps (full duplex)
- 2 auto-sensing 10/100/1000Mbps ports
- Full/half duplex support with ANSI/IEEE 802.3 NWay auto-negotiation
Topology
- IEEE 802.3x Flow Control in full-duplex, back pressure in half-duplex
Star
- 10BASE-T/100BASE-TX: full/half duplex
- 1000BASE-T: full duplex
Hardware
- MDI-II/MDI-X auto-sensing for all twisted-pair ports
Basic Configuration
- Auto-correction of twisted-pair Rx reverse polarity
- 24 auto-sensing 10/100Mbps ports (built-in)
- 10BASE-T cables:
- 1 open slot
UTP Cat. 3, 4, 5 (100 m max.)
- 100BASE-TX/1000BASE-T cables:
Switch Fabric
UTP Cat. 5/Cat. 5e (100 m max.)
8.8 Gbps
- LED report (per port):
100/1000Mbps speed
LED (per device)
Link/Act
- Power
- Console
DES-132GB GBIC Module
- IEEE 802.3z standard
Built-in Ports Supported Functions
- 2 GBIC-based ports for installation of 1000BASE-SX and 1000BASE-LX
- IEEE 802.3 10BASE-T/802.3u 100BASE-TX standards
PHY modules
- Full/half duplex support with ANSI/IEEE 802.3 NWay auto-negotiation
- Full duplex support
- IEEE 802.3x Flow Control in full-duplex, back pressure in half-duplex
- IEEE 802.3x Flow Control
- MDI-II/MDI-X auto-sensing for all twisted-pair ports
- Cables: single-mode and multi-mode fiber
- Auto-correction of twisted-pair Rx reverse polarity
- LED report (per port): Link/Act
- Port trunking: up to 8 ports per trunk, up to 8 trunks per switch
- 10BASE-T cables:
UTP Cat. 3, 4, 5 (100 m max.)
Software
- 100BASE-TX cables:
VLAN
UTP Cat. 5 (100 m max.)
- IEEE 802.1Q Tagged VLAN
- LED report (per port):
- Port-based VLAN
10/100Mbps speed
- Number of VLANs: 255 per device (max.)
Link/Act
Priority Queues (QoS)
Optional Modules
- Standard: IEEE 802.1p
DES-332GS Stack + GBIC Module
- Number of queues: 4
- 1 stacking port
- 1 GBIC port (IEEE 802.3z standard)
Spanning Tree
- Stackable units: 6 DES-3226S switches per stack
Standard: IEEE 802.1D
- Stacking method: ring
- Full duplex support for GBIC port
Multicast
- IEEE 802.3x Flow Control (GBIC port)
- IGMP v2
- Stacking cable: proprietary IEEE 1394 cable (provided)
- IGMP Snooping
- Network cables (GBIC port): single-mode and multi-mode fiber
- DVMRP
- LED report (per port): Link/Act (GBIC port)
- PIM-DM
DES-132F Fast Ethernet Fiber Module
Access Security
- IEEE 802.3u 100BASE-FX standard
- MAC based: user-specified MAC addresses
- 2 100Mbps fiber ports (SC connectors)
- VLAN based: ingress checking enable/disable
- Full duplex support
- Port based: MAC address learning per port enable/disable
- IEEE 802.3x Flow Control
- IEEE 802.1x Port-based Network Access Control *
- Cables: 50, 62.5/125-micron multi-mode fiber (2 km max.)
- LED report (per port): Link/Act
MultiLink Trunking (MLT)
Enables grouping of links between the switch and another switch or a server
DES-132FL Fast Ethernet Fiber Module
to provide higher bandwidth of up to 8 10/100 ports or up to 6 GBIC ports
- IEEE 802.3u 100BASE-FX standard
with active redundant links. A multi-link is defined as trunked ports spanning
- 2 100Mbps fiber ports (SC connectors)
multiple units of the stack for fail-safe connectivity to mission-critical servers
- Full duplex support
and the network center.
- IEEE 802.3x Flow Control
- Number of Fast Ethernet ports per trunk: 8 (max.)
- Cables: 9-micron single-mode fiber (15 km max.)
- Number of Fast Ethernet ports per multi-link trunk: 8 (max.)
- LED report (per port): Link/Act
- Number of Gigabit ports per multi-link trunk: 6 (max.)
- Number of multi-link trunks per stack: 6 (max.)
DES-132G Gigabit Fiber Module
- Operation mode: load sharing
- IEEE 802.3z 1000BASE-SX standard
- 2 Gigabit fiber ports (SC connectors)
Gigabit Port Trunks
- Full duplex support
- Number of ports per trunk: 6 (max.)
- IEEE 802.3x Flow Control
- Number of trunks per stack: 6 (max.)
- Cables: 50/125 micron multi-mode fiber (525 m max.), 62.5/125 micron
- Operation mode: load sharing
multi-mode fiber (275 m max.)
- LED report (per port): Link/Act
DES-3226S
Technical Specifications
10/100Mbps L2 Stackable Switch
Performance
Transmission Method
Emission (EMI)
Store-and-forward
- FCC Class A
- CE Class A
MAC Address Table
- C-Tick Class A
8K entries per device
- VCCI Class A
- BSMI Class A
MAC Address Learning
- Dynamic entries: automatic update
Safety
- Static entries: user-defined
CSA International
Packet Filtering/Forwarding Rates (half duplex)
- Ethernet: 14,880 pps per port
- Fast Ethernet: 148,810 pps per port
* Available in future release
- Gigabit Ethernet: 1,488,100 pps per port
RAM Buffer
8MB per device (excluding optional modules)
Configuration & Management
Management Support
- SNMP-based management v.1 (v.3 available in future version)
- Web-based management
- CLI (command line interface)
- RMON monitoring
- Telnet (up to 8 sessions)
MIBs
- MIB-II (RFC 1213)
- Bridge MIB (RFC 1493)
- RMON MIB (RFC 1757)
- 802.1Q VLAN MIB (RFC 2674)
- IGMP MIB (RFC 2833)
- If MIB (RFC 2233)
- Ethernet-like MIB (RFC 2358) - dot3statsTable
- D-Link enterprise MIB
C
I A
N
TIO
U
N
RMON Groups
M
M
C
O
O
C
M
1, 2, 3, 9 (Alarm, Statistics, History, Event)
M
L
A
I
S
I
R
S
E
IO
D E
N
F
IP Number Self-identification
U S A
Through DHCP client, Bootp client
Ordering Information
Firmware Upgrade
TFTP
10/100Mbps Layer 2 Stackable Switch
DES-3226S 24 10/100Mbps ports + 1 open slot
Console Port
DB-9 RS-232 DCE
Optional Modules
DES-332GS
1 stacking port + 1 GBIC port
DES-132F
2 100BASE-FX multi-mode fiber ports (SC connectors)
Physical & Environmental
DES-132FL
2 100BASE-FX single-mode fiber ports (SC connectors)
Power Input
DES-132G 2 1000BASE-SX Gigabit fiber ports (SC type connectors)
100 - 240 VAC, 50/60 Hz
DES-132GL
2 1000BASE-LX Gigabit fiber ports (SC type connectors)
DES-132T
2 10BASE-T/100BASE-TX/1000BASE-T Gigabit copper ports
Internal universal power supply
DES-132GB
2 GBIC-based ports
Power Consumption
29 Watts (max.)
Ventilation
40 x 40 mm DC fans x 2
Operating Temperature
0 - 50 C (32 - 122 F)
Specifications subject to change
U.S.A.
TEL: 1-949-788-0805 FAX: 1-949-753-7033 www.dlink.com
without prior notice.
Canada
TEL: 1-905-8295033
FAX: 1-905-8295095
www.dlink.ca
Storage Temperature
D-Link is a registered trademark
of D-Link Corporation/D-Link
Europe
TEL: 44-20-8731-5555
FAX: 44-20-8731-5511 www.dlink.co.uk
-25 - 55 C (13 - 131 F)
System Inc. All other trademarks
U.K.
TEL: 44-20-8731-5555
FAX: 44-20-8731-5511 www.dlink.co.uk
belong to their proprietors.
Germany
TEL: 49-6196-77990
FAX: 49-6196-7799300 www.dlink.de
France
TEL: 33-1-30238688
FAX: 33-1-30238689
www.dlink-france.fr
Humidity
Benelux
TEL: 31-40-2668713
FAX: 31-40-2668666
www.dlink-benelux.nl
5% - 95% non-condensing
Italy
TEL: 39-02-2900-0676
FAX: 39-02-2900-1723 www.dlink.it
Iberia
TEL: 34-93-4090770
FAX: 34-93-4910795
www.dlinkiberia.es
Sweden
TEL: 46-(0)8564-61900 FAX: 46-(0)8564-61901 www.dlink.se
Dimensions
Norway
TEL: 47-22-991890
FAX: 47-22-207039
www.dlink.no
441 x 210 x 43 mm (17.36 x 8.27 x 1.69 inches)
Denmark
TEL: 45-43-969040
FAX: 45-43-424347
www.dlink.dk
Finland
TEL: 358-9-622-91660
FAX: 358-9-622-91661 www.dlink-fi.com
19-inch rack-mount width, 1 U height
Singapore
TEL: 65-774-6233
FAX: 65-774-6322
www.dlink-intl.com
Australia
TEL: 61-2-94177100
FAX: 61-2-94171077
www.dlink.com.au
Japan
Weight
TEL: 81-3-5434-9678
FAX: 81-3-5434-9868
www.dlink.co.jp
China
TEL: 86-10-8809-7777
FAX: 86-10-8809-6789 www.dlink.cn
2.5 kg (5.51 lb.) (without module installed)
India
TEL: 91-22-652-6696
FAX: 91-22-652-8914
www.dlink-india.com
Middle East
TEL: 202-6356176
FAX: 202-6356192
www.dlink-me.com
South America TEL: 56-2-232-3185
FAX: 56-2-232-0923
www.dlink.cl
RECYCLABLE
South Africa
TEL: 27(0)126652165
FAX: 27(0)126652186
www.d-link.co.za
Rev. 01 (July 2002) Russia
TEL: 7-095-737-3389
FAX: 7-095-737-3390
www.dlink.ru
Taiwan
TEL: 886-2-2910-2626
FAX: 886-2-2910-1515 www.dlinktw.com.tw
Printed in Taiwan
D-Link Corp.
TEL: 886-2-2916-1600
FAX: 886-2-2914-6299 www.dlink.com.tw
DES-3226S
Technical Application
10/100Mbps L2 Stackable Switch
Document Outline